Purification of Impure Samples by Crystallization
Theory
Our Objective
Our Objective is to prepare the crystals of the following substances form their impure samples through crystallisation
- Copper sulphate
- Potash alum
- Benzoic acid
The Theory
What happens during crystallisation?
The chemicals used for various purposes should be pure, completely free from any type of impurities. Method of purification of a substance depends upon the nature of impurities present in it. There are various methods for the purification of substances, e.g., filtration, evaporation, decantation, distillation, and crystallization. Crystallisation is one of the very important purification techniques, purifying substances by removing unwanted by-products. Crystalline compounds are generally purified via this crystallisation process.
The principle behind the crystallisation is that the amount of solute that can be dissolved by a solvent increases with temperature.
In crystallisation, the impure substance is dissolved in a suitable solvent to reach its nearly saturated solution at a temperature higher than the room temperature. At this high temperature, the solute has very high solubility in that solvent, so a much smaller quantity of hot solvent is needed for dissolving the solute than the solvent at room temperature. When the solution is cooled, the pure substance is crystallised. The solution left behind is called mother liquor. All the impurities are left behind in the mother liquor. The purification method depends on the differences in solubility between the compound and the impurity.
Let us discuss the basic steps involved in the crystallisation process
Solvent and solute selection
Choosing an appropriate solvent is the important process of crystallisation, as crystallisation works only when a proper solvent is used. It is important to choose a solvent that will not dissolve the substance at room temperature. But as the temperature of the solvent increases, the solubility of the solute also increases. At the same time, the impurities that are present must either be soluble in the solvent at room temperature or must be insoluble in the solvent at a high temperature. If the solvent is not hot when the dissolution is carried out, too much solvent will be used, leading to diminished yield.
Dissolving the solute in the solvent
Add a small portion of the solvent to the beaker containing impure sample and boiling chips while the sample is heating. Stir the contents gently. Add enough solvent to dissolve the solute to get a saturated solution at the boiling point of the solvent. If too much solvent is used, the recovery of the substance will be decreased.
Filtration of the hot solution
If the hot solution contains insoluble impurities, it can be removed by the process of filtration. For this process, Place a filter paper cone in a funnel and wet the filter paper with a spray of water to fix it inside the funnel properly. Place the funnel on a funnel stand and put a china dish below the funnel.
Note: The stem of the funnel should touch the wall of the china dish to avoid the solution splashing out.
Crystallisation of the filtrate
To concentrate the filtrate, heat the china dish containing filtrate gently with constant stirring. This is done to ensure uniform evaporation and to prevent formation of a solid crust. When the volume of the solution is reduced to one half, dip one end of a glass rod in the concentrated solution and cool the drop by blowing on it. The formation of a thin crust indicates that the crystallisation point has been obtained.
Cooling the concentrated solution
Once it is determined that the solution is saturated with the compound, it is allowed to cool slowly at room temperature.
In order to cool the concentrated solution, pour the solution into a crystallising dish and keep it undisturbed. As the solution cools, crystals separate. Once the sample is cooled to room temperature, place it in an ice bath or in cold water to complete the crystallisation.
If the crystallisation does not start immediately, add a seed crystal or scratch inside the vessel containing the concentrated solution with a glass rod.
Separation and drying of crystals
The crystals formed are separated by either decanting the mother liquor or by the process of filtration. Wash the crystals with cold water or alcohol. The crystals can be dried by pressing them gently between sheets of filter paper. They can also be dried by spreading them on a porous plate or by placing the crystals in a vacuum desiccator. The crystals have a definite geometry, and therefore a definite shape.
Let us discuss the crystallisation of some samples
Crystallisation of copper sulphate (CuSO4.5H2O)
To crystallise copper sulphate, dissolve it in water and add a small quantity of dilute sulphuric acid to prevent the hydrolysis of copper sulphte. The impurities left behind in the solution are removed by filtration. The filtrate is concentrated to the crystallisation point and then cooled. On cooling, transparent blue crystals of copper sulphate separate. The copper sulphate crystal formed has triclinic shape
Crystallisation of Potash Alum
Potash alum is highly water soluble. To prepare pure crystals of potash alum, dissolve the sample in distilled water and remove the insoluble impurities by filtration. This solution is concentrated to the crystallisation point and cooled. Colourless transparant crystals of potash alum separate. The soluble impurities are left behind in the mother liquor. Potash alum has an octahedral geometry.
Crystallisation of Benzoic Acid
Benzoic acid is a colourless crystalline solid. It is highly soluble in hot water, but poorly soluble in cold water. It can be recrystallised by dissolving it in hot water. The hot solution obtained is filtered and cooled. Upon cooling, opaque white crystals of benzoic acid crystallise.
Learning Outcomes
- Students understand the term ‘crystallisation’ from the experiment.
- Students understand different steps of a crystallisation process.
- Students acquire skill to perform the crystallisation using the following;
- Copper sulphate
- Potash alum
- Benzoic acid
- Students may be able to do the experiment using other samples once they visualise the steps.
Procedure
Crystallisation of Copper sulphate
Materials Required
The Procedure
Real lab procedure
Preparation of the solution
- Take about 25-30 ml of distilled water in a beaker and add powdered crude copper sulphate while stirring the solution so that the powder dissolves.
- Keep adding the powdered sample till a little of it remains undissolved, even if it is stirred thoroughly.
- Now add 2-3 ml of dil. H2SO4 to make the solution clear. This prevents the hydrolysis of copper sulphate.
Filtration of the solution
- Take a funnel and fix a filter paper in it and clamp it to a stand.
- Place a china dish under the funnel. The stem of the funnel should touch the wall of the china dish to avoid the solution splashing out.
- Pour the solution into the funnel over a glass rod and collect the filtrate in a china dish. The insoluble impurities are left in the filter paper as residue.
Concentration of the filtrate to crystallisation point
- Heat the china dish on a sand bath till the solution is reduced to about one-third of its original volume.
- To avoid crust formation on the sides of the dish, stir the solution continuously with a glass rod. If crust is formed, it can be dissolved in the solution by removing it with the glass rod. Don’t allow the solution in the dish to boil.
- To know if the solution has reached its crystallisation point, use the end of the glass rod to remove a drop of the solution and cool it by blowing on it. The appearance of a crust or tiny crystals on the glass rod shows that the crystallisation point has been reached.
- Turn off the burner and stop heating.
- Transfer the hot saturated solution into a crystallising dish.
Cooling the hot saturated solution
- Place the crystallisation dish containing the hot saturated solution in a trough containing water filled to the brim and allow it to cool slowly for sometime.
- Deep blue crystals of copper sulphate will be formed. The crystallisation will complete after half an hour.
Separation of crystals and drying
- Decant the mother liquor carefully into a beaker.
- Wash the crystals with a little ethyl alcohol containing a small amount of cold water.
- Place the crystals on a filter paper which will soak up the solution.
- Transfer the crystals to another filter paper and dry them by pressing gently between the folds of the filter paper or by spreading on a porous plate.
- Transfer the crystals into a dry test tube and cork it.
Crystallisation of Potash Alum
Materials required
The Procedure
Real lab procedure
Preparation of solution
- Take about 25-30 ml of distilled water in a beaker. Add about 5-6 g of crude sample of potash alum to it and stir the contents of the beaker with a glass rod until the solution is clear.
- Warm to dissolve all of the alum present in the sample.
Filtration of the solution
- Take a funnel and fix a filter paper in it and clamp it to a stand.
- Place a china dish under the funnel. The stem of the funnel should touch the wall of the china dish to avoid the solution splashing out.
- Pour the solution into the funnel over a glass rod and collect the filtrate in a china dish. The insoluble impurities are left in the filter paper as residue.
Concentration of the filtrate to crystallisation
- Heat the china dish on a sand bath till the solution is reduced to about one-third of its original volume.
- To avoid crust formation on the sides of the dish, stir the solution continuously with a glass rod. If a crust is formed, dissolve it back into the solution by removing it with the glass rod. Don’t allow the solution in the dish to boil.
- To know if the solution has reached its crystallisation point, use the end of the glass rod to remove a drop of the solution and cool it by blowing on it. The appearance of a crust or tiny crystals on the glass rod shows that the crystallisation point has been reached.
- Turn off the burner and stop heating.
- Transfer the hot saturated solution into a crystallising dish.
Cooling the hot saturated solution
- Place the crystallisation dish containing the hot saturated solution in a beaker containing water filled to the brim and allow it to cool slowly for some time.
- Colourless transparent crystals of potash alum begin to separate.
- After about half an hour, the crystallisation is complete.
5. Separation of crystals and drying
- Decant off the mother liquor carefully into a beaker.
- Wash the crystals with cold solution of alcohol and water.
- Place the crystals on a filter paper which will soak up the solution.
- Transfer the crystals to another filter paper and dry them by pressing gently between the folds of the filter paper.
- Transfer the crystals into a dry test tube and cork it.
Crystallisation of Benzoic Acid
Materials required
The Procedure
Real lab procedure
Preparation of solution
- Take about 150 ml of distilled water in the beaker and boil the water over a Bunsen burner by placing the beaker over a piece of wire gauze placed over a tripod stand.
- In another beaker, take 2-3 g of crude sample of benzoic acid. While constantly stirring, gradually add a minimum quantity of boiling water just sufficient to dissolve the benzoic acid. If required, heating can be used to dissolve the benzoic acid.
Filtration of the solution
- Take a funnel and fix a filter paper in it and clamp it to a stand.
- Fix a fluted filter paper into the funnel and filter the hot solution into a beaker.
- Insoluble impurities will be left in the filter paper.
Cooling the hot saturated solution
- Let the filtered solution come to room temperature by itself.
- Now cool it by placing it in a cold water trough.
- Opaque white crystals of benzoic acid begin to separate.
Separation of crystals and drying
- Fix a filter paper in a funnel that is clamped to a stand and separate the crystals by filtration.
- Wash the crystals with cold water.
- Transfer the crystals to another filter paper and dry them by pressing gently between the folds of the filter paper.
- Transfer the crystals into a dry test tube and cork it.
Simulator Procedure (as performed through the Online Labs)
You can select any one of the sample to perform the experiment by clicking on the corresponding sample icon.
Copper Sulphate
- Drag the spatula containing copper sulphate towards the beaker containing distilled water and drop it in.
- Click on the glass rod to stir the solution.
- Drag the measuring cylinder containing conc. H2SO4 towards the beaker to pour it into the solution.
- Click on the ‘Next’ button.
- Drag the beaker towards the funnel to filter the copper sulphate solution.
- Click on the inference icon to see the inference.
- We can now click on the ‘Next’ button to go to the next process.
- Click on the knob of the burner to turn it on.
- To stir the solution in the china dish, click on the glass rod.
- Click on the inference icon to see the inference.
- Drag the china dish towards the crystallisation dish to transfer the hot saturated solution of copper sulphate into it.
- To cool the hot solution, drag the crystallisation dish and place it in the trough containing water.
- Wait for some time for the copper sulphate to recrystallise from the solution.
- Drag the crystallisation dish out of the water trough to place it back.
- Click on the inference icon to see the inference.
- We can click on the ‘Next’ button to go to the next process.
- Drag the bottle containing ethyl alcohol and water mixture towards the crystallisation dish to wash the crystals.
- Drag the crystallisation dish towards the trough to decant the upper solution.
- Click on the ‘Next’ button to go to the next process.
- Click on the inference icon to see the inference.
- To transfer the crystals into the test tube, drag the filter paper containing the crystals toward it.
- Drag the cork towards the test tube and close it.
- To redo the experiment, click on the ‘Reset’ button.
Potash alum
- Drag the spatula containing potash alum towards the beaker containing distilled water and drop it in.
- Click on the glass rod to stir the solution.
- To go to the next process, click on the ‘Next’ button.
- Drag the beaker towards the funnel to filter the potash alum solution.
- Click on the inference icon to see the inference.
- To go to the next process, click on the ‘Next’ button.
- Click on the knob of the burner to turn it on.
- To stir the solution in the china dish, click on the glass rod.
- Click on the inference icon to see the inference.
- Drag the china dish towards the crystallisation dish to transfer the hot saturated solution of potash alum into it.
- To cool the hot solution, drag the crystallisation dish and place it in the trough containing water.
- Wait for some time for potash alum to recrystallise from the solution.
- Drag the crystallisation dish out of the water trough to place it back.
- Click on the inference icon to see the inference.
- We can click on the ‘Next’ button to go to the next process.
- Drag the bottle containing alcohol and water mixture towards the crystallisation dish to wash the crystals.
- Drag the crystallisation dish towards the trough to decant the upper solution.
- Click on the ‘Next’ button to go to the next process.
- Click on the inference icon to see the inference.
- To transfer the crystals into the test tube, drag the filter paper containing the crystals toward it.
- Drag the cork towards the test tube and close it.
- To redo the experiment, click on the ‘Reset’ button.
Benzoic acid
- Drag the spatula containing benzoic acid towards the beaker containing hot water and drop it in.
- Click on the glass rod to stir the solution.
- To go to the next process, click on the ‘Next’ button.
- Drag the beaker towards the funnel to filter the benzoic acid solution.
- Click on the inference icon to see the inference.
- To go to the next process, click on the ‘Next’ button.
- To cool the hot solution, drag the beaker and place it in the trough containing water.
- Wait for some time for benzoic acid to recrystallise from the solution.
- Drag the beaker out of the water trough to place it back.
- Click on the ‘Next’ button to go to the next process.
- Drag the beaker towards the funnel to filter its contents.
- Click on the inference icon to see the inference.
- Click on the ‘Next’ button to go to the next process.
- Drag the bottle containing cold water towards the crystallisation dish to wash the crystals.
- Drag the crystallisation dish towards the trough to decant the upper solution.
- To go to the next process, click on the ‘Next’ button.
- Click on the inference icon to see the inference.
- To transfer the crystals into the test tube, drag the filter paper containing the crystals toward it.
- Drag the cork towards the test tube and close it.
Precautions
- The filtrate should be evaporated slowly by gently heating during concentration.
- The filtrate is to be evaporated only up to the crystallisation point. It should never be heated to dryness. Avoid overheating the solution.
- The solution should be cooled slowly without disturbing it. It should never be cooled rapidly.
- Wash the crystals with the washing liquid 3-4 times, using very small amount of the liquid each time.
- If the crystals obtained are very small, it means that the solution has been concentrated more than that required for the crystallisation stage.
Comments
Post a Comment